Note: This document is for an older version of GRASS GIS that is outdated. You should upgrade, and read the current manual page.

GRASS logo

NAME

r.shaded.relief - Creates shaded relief map from an elevation map (DEM).

KEYWORDS

raster, elevation

SYNOPSIS

r.shaded.relief
r.shaded.relief help
r.shaded.relief map=string [shadedmap=string] [altitude=float] [azimuth=float] [zmult=float] [scale=float] [units=string] [--overwrite] [--verbose] [--quiet]

Flags:

--overwrite
Allow output files to overwrite existing files
--verbose
Verbose module output
--quiet
Quiet module output

Parameters:

map=string
Input elevation map
shadedmap=string
Output shaded relief map name
altitude=float
Altitude of the sun in degrees above the horizon
Options: 0-90
Default: 30
azimuth=float
Azimuth of the sun in degrees to the east of north
Options: 0-360
Default: 270
zmult=float
Factor for exaggerating relief
Default: 1
scale=float
Scale factor for converting horizontal units to elevation units
Default: 1
units=string
Set scaling factor (applies to lat./long. locations only, none: scale=1)
Options: none,meters,feet
Default: none

DESCRIPTION

r.shaded.relief creates a raster shaded relief map based on current resolution settings and on sun altitude, azimuth, and z-exaggeration values entered by the user. If no output shademap name is given, the new shaded relief map is named <input_map>.shade. The map is assigned a grey-scale color table.

The module then prompts the user to enter values for:

  1. The altitude of the sun in degrees above the horizon (a value between 0 and 90 degrees), and
  2. The azimuth of the sun in degrees to the east of north (a value between 0 and 360 degrees).
  3. The name of a raster map layer to provide elevation values for the shaded relief map. Typically, this would be a map layer of elevation; however, any raster map layer can be named.
  4. The scaling parameter, which compensates for a different horizontal scale than vertical scale. If 'scale' is a number then the ewres and nsres are multiplied by that scale to calculate the shading. (Default=1.0 for equivalent horizontal and vertical scales.)
  5. For the special case when a latitude-longitude projection is used with an elevation map measured in meters (e.g., SRTM, ETOPO2 etc.) or feet, the units can be set to automatically set the horizontal scale to the the number of meters (scale=111120) or feet (scale=370400) in a degree of latitude. The script scales latitude and longitude equally, so it's only approximately right, but for shading it's close enough. It makes the difference between a usable and unusable shade. The units parameter overrides the scale parameter.
  6. The zmult exaggeration factor that changes the apparent relief for the shaded relief map. This can be any positive (or negative) floating point value. (Default=1.0)
Specifically, r.shaded.relief executes a r.mapcalc statement. Refer to the manual entry for r.mapcalc for an explanation of the filtering syntax shown in the above expression. See, for example, the section on "The Neighborhood Modifier".

r.shaded.relief then runs r.colors to assign a grey-scale color table to the new shaded relief map.

NOTES

To visually improve the result of shade maps from low resolution elevation models, use r.resamp.interp with bilinear or bicubic method to resample the DEM at higher resolution. r.shaded.relief is then run on the resampled DEM.

EXAMPLES

In this example, the aspect map in the North Carolina sample dataset location is used to hillshade the elevation map:
g.region rast=elevation -p
r.shaded.relief map=elevation shadedmap=elevation.shaded

In Latitude-Longitude locations (or other non-metric locations), the scale factor has to be used:

# Latitude-Longitude example
r.shaded.relief map=srtm shadedmap=srtm.shaded scale=111120

SEE ALSO

"r.mapcalc: An Algebra for GIS and Image Processing", by Michael Shapiro and Jim Westervelt, U.S. Army Construction Engineering Research Laboratory (March/1991) (available from the GRASS web site).

d.his, g.region, r.blend, r.colors, r.mapcalc, r.resamp.interp

AUTHOR

Jim Westervelt, U.S. Army Construction Engineering Research Laboratory

Last changed: $Date: 2011-11-08 03:23:06 -0800 (Tue, 08 Nov 2011) $


Main index - raster index - Full index

© 2003-2014 GRASS Development Team