Note: A new GRASS GIS stable version has been released: GRASS GIS 7. Go directly to the new manual page here
During the process of marking reference points with known photo coordinates, you may compute the RMS (root mean square) error for each reference point entered. i.photo.2image does this by calculating the transformation equation (the same one that is calculated by i.points ), and then plugging these results into an equation for RMS error.
i.photo.2image offers a zoom option to locate precisely the fiducial or reseau point to be marked on an image.
To run i.photo.2image, a graphics monitor is required.
The procedure for marking fiducial or reseau points, entering known photo-coordinates, and analyzing the RMS error is described below.
The terminal screen displays this message:
use mouse now...
The graphics monitor displays the following screen:
+---------------------------+---------------------------------+
|imagery | |
+---------------------------+---------------------------------+
| | |
| | |
| | |
| | |
| | |
| | |
| | |
+---------------------------+---------------------------------+
| | |
| | |
| | |
| | |
| | |
| | |
| | |
+---------------------------+---------------------------------+
| | |
+---------------------------+---------------------------------+
A pop-down menu like that shown below will be superimposed on the left half of the screen:
+------------------------------------------+
| Double click on raster map to be plotted |
| Double click here to cancel |
+------------------------------------------+
+----------------+
|Mapset imagery |
+-------+--------+
|gs13.1 | gs21.1 |
+-------+--------+
|gs14.1 | gs22.2 |
+-------+--------+
Any single file in the imagery group may be used on which to mark
points, and you may mark points on more than one file
in the imagery group to accumulate the suggested minimum number of
4-8 fiducial or ressue points.
The imagery file selected is displayed in the upper
left quadrant of the screen.
|---------------------------------------------------------------| |Camera Reference File | |---------------------------------------------------------------| | CAMERA NAME : camera name | | CAMERA ID : L1234 | | CAMERA CFL : 153.021 mm. | | CAMERA XP : 0.050 mm. | | CAMERA XP : 0.056 mm. | | number of fid. 4 | |---------------------------------------------------------------| | | |ID (X PHOTO) mm. (Y PHOTO) mm. | |_______________________________________________________________| |1 -105.023 110.123 | |2 107.987 109.834 | |3 110.965 -104.329 | |4 -103.932 -110.352 | |_______________________________________________________________|
The following menu is displayed at the bottom of the graphics display:
+-----+------+-----------+--------+---------+-------------------+-------------+ |Quit | Zoom | Plot Cell | Camera | Analyze | Input->KEYBOARD | CAMERA FILE | +-----+------+-----------+--------+---------+-------------------+-------------+
+-------+-----+-------++--------------------+ |Cancel | Box | Point ||Select type of ZOOM | +-------+-----+-------++--------------------+
You have the option of identifying the zoom window either by using the mouse to make a box, or by using the mouse to mark the center of the desired window, and adjusting the magnification factor. The terminal screen will display a mouse button menu to guide you in identifying the window. The section of the image within the zoom window will be displayed in the upper right hand quadrant.
If you wish to use the camera reference file only as a comparative reference, then the keyboard can be chosen as the means to input photo coordinates corresponding to the marked reference points on the image. This is done by placing the mouse cross hairs on the word KEYBOARD and pressing the left button on the mouse.
The following menu is displayed on the graphics terminal:
+------------------------------------+--------------------------+ |Point 1 marked at IMAGE COORDINATES | | |east: 1023.77 | | |north: 506.56 | | | | | | | | | | | | | | | | | +------------------------------------+--------------------------+ |Enter PHOTO COORDINATES as x and y: | +---------------------------------------------------------------+
You then enter the known (x,y) photo coordinates, relative to the perspective center, for the reference point marked on the image. If you do not wish to enter a coordinate, simply hit RETURN to continue; the marked reference point will disappear.
If you select the CAMERA FILE option, then reference points marked on the image will be associated with selected photo coordinates from the displayed camera reference file. In this option, when you mark a point on the image, the following menu is displayed on the graphics terminal:
------------------------------------------------------------- CANCEL Double click on the fiducial mark to be referenced -------------------------------------------------------------
If you would like to select the photo coordinates of a displayed reference mark, this can be accomplished by placing the mouse cross hairs on the reference point to be selected and pressing the left button on the mouse twice. After a reference point is selected from the display, you are prompted with "Look ok? (Y/N)". If you respond with no, the reference point is ignored. If you respond with yes, the following is displayed on the terminal:
+----------------------------------------+--------------------------+ |Point 1 marked at IMAGE COORDINATES | | |east: 1023.77 | | |north: 1065.41 | | | | | | | | |Point 1 referenced at PHOTO COORDINATES | | |X: -105.023 | | |Y: 110.122 | | | | | | | | | | | | | | | | | +----------------------------------------+--------------------------+ | use mouse now... | +----------------------------------------+--------------------------+
The photo coordinates and the corresponding image coordinates are automatically saved in the photo_points file associated with the imagery group.
+--------------------------------------------------------------------+ | error image photo | | | |# row col photo east north x y | |1 0.0 -0.9 1.0 1048.5 -144.8 -105.023 110.122 | |2 0.4 1.0 1.3 2153.1 -567.2 107.987 109.834 | |3 -1.2 -0.5 0.6 1452.8 -476.5 110.965 -104.329 | |4 1.1 0.5 1.3 1034.0 -109.2 -103.932 -110.352 | | | +--------------------------------------------------------------------+ | overall rms error: 4.46 | +--------------------------------------------------------------------+
The following menu then appears at the bottom of the monitor:
+-----+-------+------+-----------------------------------------------+ |DONE | PRINT | FILE | Double click on point to be included/excluded | +-----+-------+------+-----------------------------------------------+
The RMS error for the image is given under the column TITLEd "error" and subTITLEd "row" and "col". In the above report, point number 1 is 0.0 rows and -0.9 columns from the predicted location calculated from the transformation equation. The RMS error for the photo coordinates is listed under the heading "photo". This is the RMS error for the x and y coordinates of the photo coordinates but it is presented in the table using one general value. The overall RMS error is displayed at the bottom of the screen in milimeters. Points that create high RMS error are displayed in red on the monitor (represented here in italics).
The location of the point marked on the imagery group file is given under the heading "image" and the subheadings "east" and "north". The location of the point in the photo coordinates is given under the heading "photo" and the subheadings "x" and "y". If you would like to exclude or include a point, this can be accomplished by placing the mouse cross hairs on the point number to be included (if the point is absent) or excluded (if the point is displayed) and pressing the left button on the mouse twice. When a point is excluded, it is not afterwards included in the calculation of the RMS error, or included in the final transformation matrix. However, it can be retrieved within i.photo.2image at any time by double clicking with the mouse as described above.
An RMS error of less than or equal to approximately one resolution unit (pixel) for the image being rectified is generally considered acceptable.
Last changed: $Date: 2012-02-25 05:38:11 -0800 (Sat, 25 Feb 2012) $
Main index - imagery index - Full index
© 2003-2016 GRASS Development Team