d.rast.edit - GRASS GIS manual

Note: This document is for an older version of GRASS GIS that will be discontinued soon. You should upgrade, and read the current manual page.

NAME

d.rast.edit - Edits cell values in a raster map.

KEYWORDS

display, editing, raster

SYNOPSIS

d.rast.edit

d.rast.edit --help

d.rast.edit input=name output=name [aspect=name] [width=integer] [height=integer] [size=integer] [rows=integer] [cols=integer] [--overwrite] [--help] [--verbose] [--quiet] [--ui]

Flags:

--overwrite: Allow output files to overwrite existing files
--help: Print usage summary
--verbose: Verbose module output
--quiet: Quiet module output
--ui: Force launching GUI dialog

Parameters:

input=name [required]: Name of input raster map
output=name [required]: Name for output raster map
aspect=name: Name of input aspect raster map
width=integer: Width of display canvas; Default: 640
height=integer: Height of display canvas; Default: 480
size=integer: Minimum size of each cell; Default: 12
rows=integer: Maximum number of rows to load; Default: 100
cols=integer: Maximum number of columns to load; Default: 100

DESCRIPTION
NOTES
- Geographic Region Concerns
EXAMPLE
TODO
SEE ALSO
AUTHOR

DESCRIPTION

The d.rast.edit program allows users to interactively edit cell category values in a raster map layer displayed to the graphics monitor using a mouse cursor.

Overview window

An overview window shows the entire map with a red box showing the current editing region. The edit window shows the cells within the selected area. Click on a new spot on the overview window to move the editing area.

Raster cell editing

Cell editing is done using the mouse cursor to indicate the cell(s) on the displayed raster map that are to be edited.

To change the value of a cell put the new value to use in the "New value" box at the bottom left of the edit window. A value of "*" indicates a NULL value should be used.

Important: the new value in the "New value" box must be confirmed with ENTER, otherwise it is not yet active.

Saving the edited map

To save the edited map, the "File" menu contains the entry Save. To leave d.rast.edit, use Exit in the menu.

Map pan with arrow keys

The map can be shifted using the arrow keys on the keyboard.

NOTES

There is no "undo" command nor way to exit edit mode without saving changes to the output map.

Any MASK in place will be respected when writing the new raster map layer, including any edits to the MASKed areas.

Geographic Region Concerns

d.rast.edit reads the region definition for the raster map layer being edited from its internal cell header file. The new, edited copy of the raster layer will be created with the same resolution and region dimensions.

The primary bane of the d.rast.edit program involves large map layers with lots of rows and columns) and/or slow computers, since the program must read and write raster map layers row by row for the full size of the map layer as dictated by its region size and resolution. (The current region settings of north, south, east, and west will not limit the size of the edited copy of the map layer, since by use of the overview selection these values may change several times during the editing session).

EXAMPLE

Editing raster values in a LiDAR DEM, North Carolina sample data:

g.region raster=elev_lid792_1m -p

# pan to area of interest and edit raster cells (I used "102" as value to modifiy cells
# Use:  File > Save to save
# then: File > Exit
d.rast.edit input=elev_lid792_1m output=elev_lid792_1m_modified

# comparison of raster statistics
# original stats, note the min value
r.univar -g elev_lid792_1m

# modified map stats, note the min value
r.univar -g elev_lid792_1m_modified

Figure: Editing of pixels in an elevation raster map using d.rast.edit

TODO

d.rast.edit should not create a new raster map layer if the user makes no cell edits while running the program and leaving it without saving.

It would be nice to incorporate a scrollable version of d.legend (such that one could see a label legend for files with many categories on a standard size sub-frame). It would be even nicer to be able to select the category values from a graphical legend when editing cell values (thereby saving a trip to the text frame to type in the new value).

Perhaps method(s) for multiple or mass cell edits would be useful. This could be done by providing modes in which the user may:

edit a block of cells to a given value by drawing a box;
be able to choose a given value which is automatically used as the new value on each cell chosen until a different value is desired.

There is no user-interrupt handling. This could leave files in .tmp or (rarely) result in half-baked raster maps. The original file would survive unscathed by an interrupt at most any point in execution. Beware of exiting the program by means other than using exit on the Main Menu.

AUTHOR

Tcl/Tk (2007) and wxPython versions (2008): Glynn Clements

Replaces Xdriver version in C by Chris Rewerts, April 1991, Agricultural Engineering, Purdue University

SOURCE CODE

Available at: d.rast.edit source code (history)

Latest change: Thursday Dec 03 05:38:35 2020 in commit: 7c4aeda4142ea9870de706cc4aad5eb0479b338c